Dme Toggle-Lok (Positive early ejector return) Manuel d'utilisateur télécharger pdf

Page 1 of 5 TL-9997 03/2010

ME-0508-PS-059(B)



DME TOGGLE-LOK

POSITIVE EARLY EJECTOR PLATE RETURN

INSTALLATION INSTRUCTIONS FOR STANDARD TOP MOUNT CATALOG NO. TLTM-100

Failure to comply with these warnings may lead to

personal injury. COMPONENT FALL DUE TO

GRAVITY. PINCH OR CRUSH HAZARD.

The DME Toggle-Lok assembly is comprised of lever arms which when partially unfastened

from a mold and released, may swing down due to gravity. Care needs to be taken when

installing, adjusting or repairing this assembly, either on a bench or in an injection press.

When servicing while the mold while it is installed in an injection molding press, always

ensure the press guard doors are interlocked with the operation of the machine platens. Do

not attempt to service this product while the mold is in the press if the press guard doors are

not interlocked with the operation of the machine platens. It is safer and more effective to

service the mold when it is on a work bench. Wear proper protective equipment including

gloves and eye protection. These instructions must be passed on to the end user who

should read them carefully before using this product. Failure to do so may result in serious

injury.

Installation instructions:

The Top Mount is used when the ejector plate extends beyond the end of the mold, since it

is designed to be mounted on top of the ejector plate. Refer to the table provided in the

DME Mold Components Catalog for the specific Top Mount required for your Toggle-Lok

package.

NOTE: Please refer to the DME Mold Components Catalog page titled, “Basic Design

Guidelines for Standard Mold Bases,” for additional information.

1. Entire setup is made with mold in the fully closed position.

2. Machine clearance for the lever on either end of the mold where the housing is open for

the ejector plate and place the lever in its proper position:

a) Central to mold if style X

b) As specified in table for style Y

c) As far out from centerline of mold as possible, keeping mounts on ejector plate

for style Z.

3. Check to be sure levers, mounts, arms and joints including their mounting screws and

dowels will not interfere with other mold components through their entire movement.

4. The lead-in end of all levers must be the same height and sides must be square to the

top of the mold. Locate and drill, or transfer if lever has mounting holes for two 3/8-16

1 2 3 4 5

DME TOGGLE-LOK 1
TL-9997 03/2010 2

Résumé du contenu

Page 1 - DME TOGGLE-LOK

Page 1 of 5 TL-9997 03/2010 ME-0508-PS-059(B)DME TOGGLE-LOK POSITIVE EARLY EJECTOR PLATE RETURN INSTALLATION INSTRUCTIONS FOR STANDARD TOP MO

Page 2 - TL-9997 03/2010

Page 2 of 5 TL-9997 03/2010 ME-0508-PS-059(B)UNC S.H.C.S. Tighten S.H.C.S. and check for proper location and squareness. Maintaining corre

Page 3

Page 3 of 5 TL-9997 03/2010 ME-0508-PS-059(B)11. Repeat steps 6, 7, 8, 9, 10 on opposite end of mold. 12. Place cover plates under Top

Page 4

Page 4 of 5 TL-9997 03/2010 ME-0508-PS-059(B)NOTE: DRAWINGS BELOW ARE FOR REFERENCE ONLY, AND ARE NOT TO SCALE. ALWAYS USE PROPER TEMPLATE

Page 5

Page 5 of 5 TL-9997 03/2010 ME-0508-PS-059(B)NOTE: DRAWINGS BELOW ARE FOR REFERENCE ONLY, AND ARE NOT TO SCALE. ALWAYS USE PROPER TEMPLATE

Plus de documents pour Matériel Dme Toggle-Lok (Positive early ejector return)

Voir le document Dme Toggle-Lok (Positive early ejector return) Manuel d'utilisateur

Dme Toggle-Lok (Positive early ejector return) Manuel d'utilisateur (3 pages)

Commentaires sur ces manuels

Pas de commentaire

Dme Toggle-Lok (Positive early ejector return) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Dme Toggle-Lok (Positive early ejector return). DME Toggle-Lok (Positive early ejector return) User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Matériel Dme Toggle-Lok (Positive early ejector return)

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Dme Toggle-Lok (Positive early ejector return)